Easy Like IHCby Assay Upp
Early Access & in development · Assay Upp designs

From our bench to yours.

SlideDock and SlidePlane are available to order at introductory Early Access prices. Their core designs are established, and feedback from early users will help us refine the details.

Early Access products are available to purchase. Choose a format below and request a quotation. TMA-Upp is available to order. The multiwell plate holder remains in development.

SlideDock · Multi-slide staining trayEarly Access

Incubate and wash your slides in one tray.

No transfers between steps.

Built for manual IHC, IF and multiplex IF. Slides stay in the tray from the first antibody to the final wash, reducing handling while keeping the workflow open to your existing antibodies, kits and procedures.

Early Access prices

SEK / EUR · excluding VAT
SlideDock formatPrice (excl. VAT)
6 slides895 SEK / €81
10 slides1,295 SEK / €118
16 slides1,795 SEK / €163

Available to order. Request a quotation for your preferred format and colour.

01
Slides stay put

Fewer handling steps, with less risk of a lost or dried slide during the staining run.

02
Reagents stay undiluted

Minimal dead volume and full drainage leave little wash buffer behind to dilute the next reagent.

03
Your protocol, unchanged

No proprietary reagents and no instrument. Keep the validated antibodies, kits and procedures you already use.

A run in three steps

01Load. Place your slides in the tray.
02Incubate. Add reagent, close the lid and incubate from +4 °C to +50 °C.
03Wash in place. Wash and drain without moving the slides.

For multiplex IF: repeat incubation and wash for each cycle. Antigen retrieval, chromogen and counterstain are performed outside the tray.

Early Access specifications

Formats6, 10 or 16 slides
SlidesStandard 76 × 26 mm
ApplicationsIHC, IF, multiplex IF
Temperature+4 °C to +50 °C
HumidityHumid chamber with closed lid
MaterialPETG
ColoursBlack or misty blue; both light-tight
StatusEarly Access · available to order
Order SlideDock for your lab

Introductory Early Access pricing is available now. Request a quotation for your preferred format and colour.

Request a Quote

Research use only. Not for use in diagnostic procedures.

SlidePlane · Flat-slide humidity chamberEarly Access

Incubate slides flat. Move them all in one lift.

Flat, warm, humid incubations — without slide-by-slide transfers.

SlidePlane holds up to 12 slides flat at the same height, keeping small reagent drops in place during incubation. Transfer the full set of slides to the wash tray together, or wash in the chamber itself.

Early Access prices

SEK / EUR · excluding VAT
SlidePlane configurationPrice (excl. VAT)
Basic · 10 slides1,295 SEK / €118
Basic · 12 slides1,495 SEK / €136
Extended · 10 slides1,895 SEK / €172
Extended · 12 slides2,095 SEK / €190

Extended = Basic + 600 SEK (approximately €54); includes a separate wash tray with light-tight lid.

01
Flat and level

Slides lie at the same height, supporting even warming and controlled small-volume incubations.

02
All slides in one lift

Move the entire run between incubation and washing without individual transfers using forceps.

03
Keep the chamber warm

Leave the humid chamber in an oven or incubator so the next step starts warm and humid.

04
Keep washes dark

The Extended kit adds a separate wash tray with a light-tight lid to limit light exposure between fluorescent staining cycles.

A run in three steps

01Load. Lay 10 or 12 standard slides flat and add reagent to each.
02Incubate. Close the gravity lid and incubate at room temperature or in a pre-warmed humid chamber (up to 45 °C).
03Wash. Transfer all slides in one lift to the wash tray, or wash in the chamber itself. Use the covered wash tray between fluorescent cycles to minimise light exposure.

Designed for repeated cycles: repeat incubation and washing for IHC, IF, multiplex IF, HCR and enzymatic workflows such as PLA or TUNEL. The gravity lid uses a labyrinth edge to help maintain humidity and reduce light exposure during fluorescence steps.

Early Access specifications

Formats10 or 12 slides
SlidesStandard 76 × 26 mm
ApplicationsIHC, IF, mIF, HCR, PLA, TUNEL
Temperature+4 °C to +45 °C
HumidityWetted pad in a closed chamber
Wash volumeApprox. 210 mL (12-slide tray)
FootprintApprox. 22 × 19 cm; 3.3 cm high with lid
Material / colourPETG · blue
Basic kitHumidity chamber with lid
Extended kitAdds wash tray with light-tight lid
StatusEarly Access · available to order
Order SlidePlane for your lab

Choose Basic or Extended at introductory Early Access pricing. Request a quotation for your preferred configuration.

Request a Quote

Research use only. Not for use in diagnostic procedures.

Project 03 / 03In development

Ergonomic multiwell plate holder

Adjustable support for ergonomic manual work with multiwell plates.

What we’re addressing

Long pipetting sessions and repeated access to wells can make a flat plate an awkward working surface. Spend hours working at that angle, and your wrist may start to feel it. A more comfortable plate position could make repetitive work easier on your hands - and your experiment easier to get through.

What we’re exploring

Exploring a stable, angle-adjustable plate support that improves access and supports more comfortable wrist positioning, while keeping the footprint practical for a crowded bench.

Share a workflow suggestion →
Your bench, too

Is there a small workflow problem worth solving?

Development starts with practical observations. If one of these projects matches a problem in your lab, tell us what would make the tool useful for your workflow.

Share a workflow challenge →

Interested in a product that is already part of the launch range? Browse the current catalogue.